4.7 · 55 Google reviews Mon–Fri, 7 AM–5 PM Greenville, OH · Serving western Ohio & eastern Indiana

Repair · Leaks

How Do You Fix a Leaking Metal Roof?

You fix a leaking metal roof by finding where water actually gets in, then repairing that part: replacing backed-out screws and dried-out washers, re-flashing chimneys and walls, swapping cracked pipe boots, resealing laps or replacing a damaged panel. Water travels along panels and underlayment, so the drip inside is rarely under the hole. Caulk over a leak is a stopgap, not a repair.

By Isaac Smith, Brothers Metal Roofing · Updated November 2026

New endwall flashing set against the wall before standing seam panels on a Xenia, Ohio farmhouse

Where do metal roofs leak?

  • Exposed screws and washers. On rib and corrugated panels, rubber washers dry out and screws back out over the years.
  • Flashing. Chimneys, sidewalls, endwalls and valleys: anywhere the roof meets something else.
  • Pipe boots and vents. Rubber boots crack in the sun, and vent caps break.
  • Laps and transitions. Where panels overlap, or where a low slope meets a steep one.
  • Ridge cap and trim. Closures can shift or blow out in high wind.
  • Rust-through. Old panels that have rusted through at laps, cut edges or screws.

How to find a metal roof leak before you fix it

Water travels. It runs along the underside of panels, across underlayment and down rafters, so the stain on your ceiling is rarely under the opening. Start in the attic after a rain with a flashlight. Look for wet decking, darkened wood or drips, then follow the trail uphill toward the nearest screw line, pipe, chimney or wall.

If the attic does not tell you, a hose test can. One person runs water on the roof, starting low and working up one section at a time, while a second person watches inside. Treat that as a job for a roofer with fall protection, because a wet metal roof is too slippery to stand on. See can you walk on a metal roof?

Fixes that last and fixes that do not

ProblemLasting fixStopgap
Backed-out screw or dried washerNew screw and washer, sometimes one size upCaulk over the screw head
Gap at a chimney or wallRe-flash, with flashing tucked behind the siding where possibleSealant smeared along the joint
Cracked pipe bootReplace the bootTape or caulk around the pipe
Leaking lap on rib panelsClean, reseal and re-fasten the lapRoof coating over the top
Rusted-through panelReplace the panelPatch over the hole

A stopgap has its place when rain is coming and a crew is days away. Just know what it is. Paint and roof coatings will not stop leaks either; see can you paint a metal roof?

When does a leak mean it is time to replace?

A repair makes sense when the panels are sound and the problem is a few screws, a boot or a piece of flashing. Replacement starts to make more sense when rust has eaten through in several places, when the roof leaks somewhere new every season, or when the decking underneath has gone soft. We will tell you which one you are looking at.

Sometimes a repair is all it takes, even on a stubborn leak. One customer’s pole building had leaked since the day it was built, and the builder’s fix had not held. After our repair, they wrote that “where there used to be puddles on the floor it is dry as can be.” Two recent Google reviewers put their repair costs in the $1,000 to $5,000 range, for a pole-building leak and a full porch roof.

Can you fix a leaking metal roof yourself?

On a low shed or barn with exposed screws, replacing a few backed-out fasteners from a ladder is a reasonable weekend job. On a house, most leaks sit at flashing details that are easy to make worse, and the fall risk is real. If you are not sure what you are looking at, take photos from the ground and ask. One homeowner, Nathan F., called Isaac about a metal job another contractor was doing; Isaac asked for pictures and gave him a list of questions to ask.

You can do the same: text photos of the problem to (937) 423-9352 for a first look.

What causes most of the leaks we see?

Our area has a lot of very old metal roofs, and they show every kind of wear. On our service calls, the most common leak sources are pipe boots, chimneys, vent boxes and dormers: the places where something passes through the roof or a wall meets it. That is why a good repair starts at those details before anyone blames the panels.

Our take. Fixing a leaking metal roof starts with finding the real source, and we repair metal roofs we did not install. See metal roof repair or call (937) 423-9352, Mon–Fri, 7 AM–5 PM.

Related questions

Straight answers

Frequently asked questions

Can you use caulk to fix a metal roof leak?

Only as a short-term patch. Caulk over a screw, lap or flashing gap usually does not last. The lasting fix is to replace the screw, washer, boot, flashing or panel that is letting water in.

Why is my new metal roof leaking?

Leaks on new metal roofs almost always come from the details: flashing at chimneys and walls, pipe boots, valleys or trim. Call the installer first, since the work should be under their warranty.

How much does it cost to fix a leaking metal roof?

It depends on the cause. Replacing a few screws or a pipe boot costs far less than re-flashing a chimney or replacing panels. Brothers Metal Roofing quotes repairs on site for free; two recent customers reported repair costs in the $1,000 to $5,000 range.

Free estimates · Mon–Fri, 7 AM–5 PM

Let’s look at your roof.

Free inspection and a written estimate. No pressure, and an honest answer on repair vs. replace.

(937) 423-9352
  • 5265 Sebring Warner Rd, Greenville, OH 45331
  • 40-yr Double Lock Warranty
  • 4.7 from 55 Google reviews

Get your free estimate

Fill out our short form and we reply within one business day, usually sooner.

  • Free, written estimate
  • No-pressure roof inspection
  • Honest repair-or-replace advice
Request my free estimate Call (937) 423-9352

Mon–Fri, 7 AM–5 PM

Call nowFree estimate