Standing seam cost by roof size
| Roof area | Squares | Standing seam, installed |
|---|---|---|
| 1,000 sq ft | 10 | $8,000 to $16,000 |
| 1,500 sq ft | 15 | $12,000 to $24,000 |
| 2,000 sq ft | 20 | $16,000 to $32,000 |
| 2,500 sq ft | 25 | $20,000 to $40,000 |
| 3,000 sq ft | 30 | $24,000 to $48,000 |
These are roof areas, not floor areas. Overhangs and pitch make a roof larger than the house under it, so a 1,500 sq ft ranch can have close to 2,000 sq ft of roof. See how much a metal roof costs on a 1,500 sq ft house, or work out your own with the metal roof cost calculator.
Double lock vs. snap lock: what the price difference buys
| Double lock | Snap lock | |
|---|---|---|
| Installed price | Upper part of $8 to $16 / sq ft | Within $8 to $16 / sq ft |
| Seam | Folded over twice with a seamer along every panel | Snaps together over concealed clips |
| Lowest pitch we install | 1:12 | 3:12 |
| BMR warranty | 40-year Double Lock Warranty | 30 years |
Double lock costs more because every seam is folded twice with a seamer along the full length of each panel, which takes more time on the roof. That folded seam is why we can put 40 years in writing and install it on slopes down to 1:12. Both warranties can be transferred one time to a new owner.
What is in a Brothers Metal Roofing standing seam price
- Tear-off to the decking, and never installing over rotten or damaged decking. Bad boards are replaced with new OSB.
- Ice and water shield and synthetic underlayment under every roof.
- Trims and flashings installed before the panels, so the hard details are done first.
- Panels roll-formed on site, 16 inches wide and one piece from eave to ridge.
- Galvalume steel with SMP paint, in 24 or 26 gauge, smooth or textured. Popular colors are black, charcoal, midnight gray, burnished slate, cocoa brown and green.
- A continuous vented ridge on every standing seam roof.
- A written warranty, transferable once.
What moves a standing seam price up or down
- Pitch. Steeper roofs need more safety setup and go slower.
- Complexity. Valleys, hips, dormers, chimneys and skylights each add trim, flashing and labor.
- Tear-off. One layer of shingles is quick. Old metal over cedar shake is not.
- Gauge. 24 gauge is thicker, heavier steel than 26 gauge and costs more.
- Extras. Seamless gutters and guards, snow guards and chimney work.
More detail in the metal roof cost guide.
Standing seam vs. other roofs on price
| Roof | Price compared with standing seam | BMR warranty |
|---|---|---|
| Asphalt shingles | A standing seam quote is usually about 2.5 times a shingle quote on the same house | We install metal only |
| TuffRib / PBR exposed fastener | Only slightly more than shingles | 20 years labor and material |
| Painted metal shingles | About 15% more than standing seam | 30 years |
| Copper | Highest; quoted by estimate | Ask us |
Why standing seam costs more than exposed-fastener metal
Standing seam hides its fasteners. Clips screwed to the deck sit under the seam, so no screws go through the face of the panel and the panels can expand and contract. Exposed-fastener panels are screwed straight through the face, and each screw relies on a rubber washer that ages. We recommend checking those roofs at 10 years, 15 years, then every 5. Standing seam costs more up front and asks for less attention over its life. More in standing seam vs. exposed fastener.
A real roof, worked out
Our Lynn, Indiana re-roof was 26-gauge, 1.5-inch double lock standing seam on about 1,900 sq ft of roof. At $8 to $16 per square foot, a roof that size works out to roughly $15,200 to $30,400 before extras, and double lock sits in the upper part of that range. That job also needed three old roofs torn off and new decking. This is arithmetic on our published range, not that customer’s invoice.
Our take. How much does a standing seam metal roof cost? Plan on about $8 to $16 per square foot installed, with double lock at the upper end. Our estimates are free and written, with the panel, gauge, color, warranty and scope spelled out. Call (937) 423-9352.

